9330-7101-001V8.3GRevD11/97™INSTALLATIONINSTRUCTIONSKP96/KP97SERIESKEYPANELSVERSION8.3GWITHEKP96/EKP97EXPANSIONPANELSANDLCP-100ALEVELCONTROLPANELADAM™
•ADAM CS with RJ-11 or DB-9 back panel: Youcan determine the correct logical keypanel addressfrom the worksheet in either of two ways: 1) If youknow t
☞Note that 9-pin intercom cables for use with anADAM CS frame must use special connectors at theintercom matrix end as shown in Figure 4.2.7 OPTIONAL
12 Installation Instructions, KP96 / KP97 Series KeypanelsEXPANSION PANEL 1CONTROLEXPANSIONKEYPANELEXPANSIONKEYPANELEXP. DATA INEXP. DATA OUTLCP-100AL
2.7.2 Rear Panel Headset ConnectionTable 7 lists the HEADSET connector pin functions. Avariety of headset types can be connected. Head-set/speaker swi
2.8 POWER-UP AND OPERATIONAL CHECKPlug in the ac power cords on the keypanel and any con-nected expansion panels and level control panels. Whenpower i
Installation Instructions, KP96 / KP97 Series Keypanels 15P2J202J203J201P6J403J402J401Q402J406J404J405P4U203TP 407P1U309U302U305U314P10P11SW1Y301RV201
2 and 3 are shorted, the signal is muted by 15 dB whenany Talk keys are pressed.3.1.3 J203 (SIDETONE MUTING)When pins 1 and 2 are shorted, the sideton
4. Check the level at the MIC PRE OUT connector (refTable 6 for pin-out). It should measure +8 dBu.5. If the reading is not +8 dBu, but within a 3dB r
Headset Carbon-Mic Level1. Insert a -25dBm signal (1 KHz at 50 ohms) into thecarbon mic input of the HEADSET connector(reference Table 7 for pin-out).
8. Adjust RV204 (internal) for a minimum commonmode signal.9. Insert a +8dBu (1 KHz) signal into the EXT LINE INconnector and record the output readin
2 Installation Instructions, KP96 / KP97 Series KeypanelsPROPRIETARY NOTICEThe RTS product information and design disclosed herein wereoriginated by a
20 Installation Instructions, KP96 / KP97 Series KeypanelsAddress Intercom Port Numbers (8 Ports per Audio I/O Card)1 1 9 17 25 33 41 49 57 65 73 81 8
Installation Instructions, KP96 / KP97 Series Keypanels 21NOTES
™
Installation Instructions, KP96 / KP97 Series Keypanels 3
4 Installation Instructions, KP96 / KP97 Series KeypanelsThis page intentionally left blank.
Installation Instructions, KP96 / KP97 Series Keypanels 5TABLE OF CONTENTSINTRODUCTION ·······························································
6 Installation Instructions, KP96 / KP97 Series KeypanelsAUDIO LEVEL ADJUSTMENTS ...16GENERAL ...
1 INTRODUCTIONThis manual describes the installation of the KP96 andKP97 Series Keypanels and their accessories, the EKP96and EKP97 Series Expansion P
2 INSTALLATION2.1 GENERALInstallation consists of the following general steps:1. Unpack and inspect the equipment.2. Check that the factory default ju
2.2 UNPACKING AND INSPECTIONAs soon as possible after receipt, inspect the container(s)and contents for physical damage that may have occurredin shipp
Commentaires sur ces manuels