RTS KP-98 Manuel d'utilisateur

9350-7497-001 Rev G November 2005User InstructionsDKP-8, DKP-12, AND KP-12 KEYPANELSPUSH-BUTTON AND LEVER KEY VERSIONSup to and including firmware ver

Menu List for DKP-8, DKP-12, and KP-12 Keypanels4PAGE 1-4 See “Top Level Menu, Page (1-4)” on page 22.Changes setup pages on the keypanel or any conne

5• Although the DKP-8 has an expansion connector for connection of expansion panels and level control panels, this feature is generally not used, sinc

Menu List for DKP-8, DKP-12, and KP-12 Keypanels6• Although the DKP-12 has an expansion connector for connection of expansion panel and level control

7FIGURE 3. KP-12 Keypanel Reference View (Push-button version shown).

Menu List for DKP-8, DKP-12, and KP-12 Keypanels8

9CHAPTER 2Power-Up and Initial SettingsApplying PowerVersions with an AC power connector have a power switch on the back panel. Versions with an exter

Power-Up and Initial Settings10Setting the Address1. While SET ADDR is displayed, tap the SELECT control.ADDR 1 will display in the call waiting windo

11CHAPTER 3Basic Intercom OperationKeys and Displays• Keys that are assigned for talk or talk+listen are indicated using UPPER CASE letters in the alp

Basic Intercom Operation12NOTE: You can adjust the amount of time that displays will flash for incoming call indication. See “Menus, SERVICE, TALLY” o

13CHAPTER 4Telephone OperationNOTE: KP-12 and DKP-12 Only, Requires optional TIF Interface.If the intercom system is equipped with an optional TIF tel

PROPRIETARY NOTICEThe product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex rese

Telephone Operation14Hanging Up1. Turn the SELECT control to display HANG UP, then tap SELECT.The call waiting window will display TAP KEY.2. Tap the

15CHAPTER 5Using the Top-Level MenuGeneral DescriptionWhen the keypanel is turned ON, it resets to the top-level menu. At this level, the MENU indicat

Using the Top-Level Menu16Top Menu Level, Call List NamesAs mentioned previously, a flashing CALL indication occurs when there is an incoming call fro

17Top Level Menu, DisplayTop Level Menu, Display, KEY ICOMWhen you select KEY ICOM, the intercom system names for all talk key assignments will appear

Using the Top-Level Menu18Top Level Menu, Display, ListenWhen you tap LISTEN, the listen key assignment for each key will appear in the alphanumeric d

19Top Level Menu, Key ListTop Level Menu, Key ListWhen you select Key List, the list of all currently assigned keys on all 4 setup pages will be scrol

Using the Top-Level Menu20•If restrictions against key assignment have been imposed using the intercom system configuration software, the intercom key

21Top Level Menu, Lists1. To talk to the selected IFSL, press and hold the SELECT control. This will also add the IFSL name to the call list for futur

Using the Top-Level Menu221. To talk to the selected special list, press and hold the SELECT control.2. To assign the special list to an intercom key

23Top Level Menu, TGL LISN (Toggle Listen ON/OFF)options did not stay with keys as setup pages were change. This meant that if you changed setup pages

TableofContentsREAD ME FIRST ...

Using the Top-Level Menu24

25CHAPTER 6Menu ModeSelect Control Operation in Menu Mode• The keypanel normally operates at the top-level menu. At this level, the MENU indicator is

Menu Mode26Menus, Autodial (for KP-12/DKP-12 Only)NOTE: This menu is used to store autodial numbers. To assign a key that dials a specific autodial nu

27Menus, KEY ASGN10. Use the “Menus, SERVICE, SAVE CFG” on page 44, to store your changes. Otherwise, the autodial numbers will be lost when the KP-12

Menu Mode28• Auto-function key assignment changes are automatically uploaded to the intercom system and saved to the online configuration.3. Double-ta

29Menus, KEY ASGNTo copy the TALK assignment, turn the SELECT control to display TALK, then tap SELECT.TAP DEST will appear in the call waiting window

Menu Mode30Menus, KEY ASGN, LISTSGeneral DescriptionThis menu gives you complete control when setting up key assignments. You can assign keys for any

31Menus, KEY ASGNChanging a key’s assignment has no effect on any key options that may already be assigned to that key using “General Description” on

Menu Mode324. Tap SELECT.The call waiting window will display TAP KEY.5. Tap an intercom key to assign the party line.If restrictions against key assi

33Menus, KEY ASGNChanging a key’s assignment has no effect on any key options that may already be assigned to that key using “General Description” on

TableofContentsTop Level Menu, Display, Level 2 ...

Menu Mode341. When you select PHONE, the point-to-point scroll list will display for the currently selected intercom system.2. Turn the SELECT control

35Menus, Key Opt Menu4. Tap the intercom key that you want to assign the UPL. The name UPL will appear in the display above the key.If restrictions ag

Menu Mode362. Turn the SELECT control to display CHIME2 or CHIME3 if desired, then tap SELECT. You will hear an audible sample of the chime tone. The

37Menus, Key Opt Menu3. Tap the intercom key that will be the group master key.The talk and listen indicators for the selected key will flash green, d

Menu Mode38Menus, SERVICE MENUGeneral DescriptionUse this menu to set the logical keypanel address during installation and to set general operating fe

39Menus, SERVICE MENU1. Select MENUS, SERVICE, LOCK.The call waiting window will display TAP CODE.2. Enter a 4-digit passcode by tapping intercom keys

Menu Mode40Menus, SERVICE, MIC GAINMIC GAIN adjusts mic gain from -15dB to +15dB. The default setting is 0dB. 1. To change the setting, select MIC GAI

41Menus, SERVICE MENUTo set up KP-12 and EKP MOD numbers refer to the “Procedure to Assign MODS”, below.Procedure to Assign MODSIf the keypanel is cur

Menu Mode42Using Multiple Expansion Panels (KP-12 Only)When using multiple expansion panels, some MOD numbers may have to be reassigned so that each g

43Menus, SERVICE MENU1. After selecting MUTE LVL, turn the SELECT control to select either HDPHONE or SPEAKER, then tap SELECT again. The current muti

TableofContentsMenus, KEY ASGN, UPL ...

Menu Mode44Menus, SERVICE, OUT CTRLOUT CTRL gives you the choice to listen to audio through either HEADSET or SPEAKER no matter what MIC is selected o

45Menus, SERVICE MENUSetting the Keypanel Address1. While SET ADDR is displayed, tap the SELECT control.ADDR 1 will appear in the call waiting window.

Menu Mode46•The call waiting window will display TAP KEYS. 4. If you tap any intercom key, the display above that key will briefly display OK. If you

Table 7: Correspondence between ADDR numbers and intercom port numbers for ADAM and ADAM CS Intercom SystemsSettings for ADDRIntercom Port Numbers1 1

4 404 412 420 428 436 444 452 460 468 476 484 492 500 508 516 524 532 540 548 556 564 572 580 588 5965 405 413 421 429 437 445 453 461 469 477 485 493

49Appendix AKP-12 Audio Transmit Board ConnectionsThe new audio transmit board (9030-7725-500), if used with the new controller board (9030-7725-000)

50IMPORTANT! - If you are using an earlier model KP-12, and your audio transmit board needs to be replaced, you will need to make the following adjust

51Appendix BReplacing the KP-12 Power SupplyReplacing the KP-12 Power SupplyThese instructions explain how to replace the old KP-12 power supply (part

52NOTE: If you have an older chassis, you will need to attach the 3 metal tabs as shown in the figure below. You will also need to use the supplied w

53

TableofContents

12000 Portland Avenue South • Burnsville, MN 55337 • U.S.A

1READ ME FIRSTREAD ME FIRSTThis manual is designed for two basic types of users: 1) those who are not involved in the setup or maintenance of the key-

2

3CHAPTER 1Menu List for DKP-8, DKP-12, and KP-12 KeypanelsTOP LEVEL MENU. With the MENU indicator OFF, turn the SELECT control to view the following i